Adventist Youth Honors Answer Book/Recreation/Snowshoeing - Advanced

3. Using one of the following, create a presentation that describes the origin and history of snowshoeing, including the use among native American peoples. List all sources used.
The following resources might prove useful for this requirement:
 * History of Snowshoeing by Jim Tucker
 * Snowshoe by Angela Woodward

a.Electronic presentation
An electronic presentation could be a web page, or a PowerPoint presentation. If you cannot afford (or do not have) PowerPoint, which is part of Microsoft Office, you could use OpenOffice.org's Impress instead. It's available free of charge.

b.Bulletin board/presentation board display
A display like this could be shown at a Pathfinder Fair.

For a bulletin board you will need the following items:
 * Stapler: A stapler will be used to mount everything to the bulletin board.
 * Push pins: These can be used to hold larger items to the board.
 * Roll of solid paper: Ideally, one sheet should cover the entire board. Paper is sold in rolls at teacher-supply or office supply stores.
 * Bulletin board border: The border should be themed to match your display. A variety of borders are available at teacher supply or office stores.
 * Letters: Bulletin board letters come in a variety of sizes, colors, and fonts. Again, check teacher supply or office supply stores.
 * Illustrations & photographs: Find photos and illustrations on the Internet, or draw them yourself. Print them out and use scissors to cut out the relevant parts of the photo.
 * Other display items: You could even mount a pair of snowshoes to the bulletin board, but be careful to not damage either the snowshoes or the bulletin board.

Bulletin boards usually start with a layer of solid-colored paper, followed by a border which is stapled around the edges. Before you begin, plan out your bulletin board. Lay the photos and letters out on a table and experiment with different layouts. When you find a combination you like, begin stapling your display to the bulletin board's background.

c.Verbal presentation
A verbal presentation would work best if snowshoeing equipment is used as a visual aid. Since this presentation is to cover the origin and history of snowshoeing, it would be a good idea to have both a pair of modern snowshoes and a classic wooden pair.

d.Written report (minimum of one-page)
You can prepare a report using a word processor. If your instructor allows, you could also type it up in an email, or as a blog post.

4. Review the basics of Snowshoeing safety as outlined in the Snowshoeing Honor.
The safety practices are found in requirement 5 of the Snowshoeing honor.

a.Make a pair of functional “survival snowshoes” out of native and first aid materials that would likely be available to you in a survival environment.
A pair of survival snowshoes can be made from green wood, some sort of cordage (rope, wire, strips of cloth, etc), and a knife. The first step is to find a living tree tall with a trunk roughly  in diameter. Make sure you have permission from the land owner before doing this - it will kill the tree. Alternatively, you can make the snowshoe from a living branch of a much larger tree. Bend the tree into a loop, and bind its top to its trunk with a short length of rope. Diagonal lashing will work great for this (see the ../Knot Tying/ honor for instructions on tying a diagonal lash as well as the other knots in these instructions). You could also cut the tree down before working on it, but by saving that as the last step, your work is held at chest-height, so you don't have to kneel in the snow as you work. This also lets you try several trees without damaging them while searching for one that it the proper length.

The next step is to begin weaving green twigs into the frame. Dead twigs will not work here, as they will snap - if not while you are weaving them in, then when you put your weight on them as you use the snowshoes. Start by using the branches of the tree you bent into a hoop. Then strip small branches from other trees and add them in. These twigs and branches need only be in diameter or so. Lay some of them in lengthwise, and others in crosswise. Ultimately, you want to form a webbing with gaps. Tighter webbing will allow you to walk on fluffier snow, but it will not allow snow to fall through the webbing (and off the deck) when you lift your feet.

Once the webbing is complete to your satisfaction, you will need to find another branch about in diameter to form a crossbar. An ideal candidate for this is the lower portion of the tree trunk from which your snowshoe is made. Cut the snowshoe off the tree. Then place it next to the remaining trunk to measure how long the crossbar should be. If you cut it too short, you will have to find another. If you leave it too long, you will have an awkward pair of snowshoes. The crossbar should extend beyond the frame a distance approximately equal to its thickness. Attach both ends of the crossbar to the frame at the frame's widest section using square lashing. If you are short on rope, but have some woodworking skill and plenty of time for construction, you could also carve tenons and the crossbar and cut mortices in each side of the rim. If you opt for this approach, be sure the tenons are long enough that the crossbar will not fall out. Also be sure the mortices do not remove too much wood from the rim.

Once the crossbar is firmly attached to the frame, get another length of rope to serve as the binding. Tie it to the crossbar next to where the edge of your foot will be placed using two half-hitches. Then place the foot on the snowshoe and run the binding beneath the bottom shoelace on your boots (if your boots have laces).

The next several knots form a "trucker's hitch" which is not shown in the ../Knot Tying / honor, but which is nonetheless, a highly useful knot for securely binding a load. It starts with a slip knot tied above the middle of the foot. This slip knot should be tied such that the loop will tighten when the free end is pulled (rather than when the standing end is pulled). The free end is then run beneath the crossbar on the other side of the foot, opposite the two half hitches previously tied. Then the free end runs into the loop formed by the slip knot. Tie it off with two half hitches. If you have rope leftover, run it behind the heel and tie it to the toe strap with two half hitches.

At this point, your first snowshoe is complete and ready for use. All that remains is to make a second shoe. However, since this will destroy a tree, you should probably skip the second snowshoe unless you are indeed in a survival situation. Instead, try the improvised snowshoe out by using a regular snowshoe with it. This will allow you to compare the performance of your creation with a standard snowshoe. You should find that it performs remarkably well.

b.Make a traditional set of functional snowshoes from natural and/or synthetic materials.
==6. Successfully complete two three-mile snowshoe hikes. Make a detailed report describing the approximate depth and condition of the snow, plants and animals, and the approximate speed at which you traveled.== Once you've gotten the hang of snowshoeing, you will be ready to tackle more ambitious hikes. For these, you can use regular hiking trails.

You can also tow extra gear (or small children) on a sled with little additional effort, meaning you can take equipment (or family members) that you would otherwise have to carry. Such extras could include camera equipment, lunch, camp chairs, and even a grill for cooking your food or warming some apple cider. This is a distinct advantage that snowshoeing holds over hiking.

To get your approximate speed, time yourself as you travel (stop the clock when you stop to rest for an extended period). Take along a GPS receiver so you can track where you've been (and thus, the distance you've covered). [maps.google.com Google maps] has tools available to measure distance as well, but it's not always easy to tell where you've been by looking at an online map or satellite image. You can also determine distance covered by using a topographical map. Once you know how far you've gone and the amount of time it took you to cover that distance, your speed is simply distance divided by time:

$$speed = \frac{distance}{time}$$

If your distance is measured in miles and time is measured in hours, speed will be in miles per hour. To convert hours and minutes to just hours, divide the minutes by 60 and add it to hours:

$$hours = whole hours + \frac{minutes}{60}$$

Thus, two whole hours plus 18 minutes would be:

$$hours = 2 + \frac{18}{60} = 2 + 0.3 = 2.3$$

If you covered 4.5 miles in that period of time, that would be

$$speed = \frac{4.5}{2.3} = 1.95 MPH$$

7. After one of your hikes, write a paragraph exploring the spiritual dimensions of snow. Be sure to include at least three Scriptural references to snow.
Consult a concordance or search for "snow" in an online Bible. Read several of these passages and see what sort of spiritual lessons you can take away from them. Also think about the things you experienced on your hikes. Snowshoe hikes are often serene and peaceful and filled with inexpressible beauty. Is that what you experienced?